View and Download Seiko BP-9000 owner's manual online. BUSINESS PRINTER. BP-9000 Printer pdf manual download. My company has this SEIKOSHA BP-9000 dot matrix printer. Need to check Seikosha BP-9000plus can support windows 7. I need a service manual for epson dfx 9000.
Warning “This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in strict accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient the receiving antenna — Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. “It is necessary to use shielded interconnect cables to insure compliance with FCC Class B limits for radio frequency emissions.' Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This manual and the program samples described in it are copyrighted by SEIKO Precision Inc. With all rights reserved. No part of this publication may be reproduced, stored in a r e t r i e v a l s y s t e m, o r t r a n s m i t t e d, i n a n y f o r m o r b y a n y m e a n s, m e c h a n i c a l, photocopying, recording or otherwise, without the prior written permission of SEIKO Precision Inc.
HP is a registered trademark of HEWLETT-PACKARDCompany. PCL is a registered trademark of HEWLETT-PACKARDCompany. DeskJet 500/RuggedWriter 480 are a registered trademark of HEWLETT-PACKARDCompany. Epson is a registered trademark of S.Epson Corporation. LQ-2550is a registered trademark of S.Epson Corporation. IBM is a registered trademark of International Business Machines Corporation. IBM2931 is a registered trademark of International Business Machines Corporation.
It is an open system in which business proprietors can participate voluntarily. The targeted products are office equipment such as computers, displays, printers, facsimiles, and copiers.
Their standards and logos uniform among participating nations. Contents U n p a c k i n g t h e p r i n t e r. 1 Q u i c k s t a rt u p. Introduction Features. 3 Options and expendables.
4 Printer description. Setting up Installing the paper rack. 1 0 Installing the sound seal cover. 1 0 Installing the ribbon cassette.
11 Connecting the computer. 1 2 Connecting the power cord. 1 2 Loading the paper. 1 3 Adjusting print head position.
Control panel and operations Control panel and indicators. 1 6 Paper parking. 2 0 Printing test pattern.
2 1 Demonstration print-out. 2 2 Tearing off a form. 2 2 Power-on operation summary.
Basic setup options About basic setup options. 2 4 Printing multipart paper. 2 6 Selecting page length for fanfold paper. 2 6 Selecting single sheet paper size. 2 7 Selecting font style. 2 8 Selecting character spacing.
2 9 Enlarging/compressing print. 3 0 Setting top of form position.
3 1 Loading user setup options. Extended setup options About extended setup options. 3 3 P r i n t e n h a n c e m e n t 1 0 Emulation. 3 6 11 Character table (HP mode). 3 6 1 2 Character table (Epson mode). 3 7 1 3 Character table (IBM mode).
3 7 1 4 National font style. 3 8 1 5 Code page. 3 8 1 6 IBM Alternate graphic mode. 3 9 1 7 Carriage return (CR). 3 9 1 8 Line feed (LF).
4 1 2 4 Lock-in the font. 4 1 2 5 Lock-in the character spacing. 4 1 2 6 Lock-in the print quality. B a r c o d e p r i n t e n h a n c e m e n t 2 7 Enable barcode print. 4 2 2 8 Barcode type. 4 2 2 9 Bar code size. 4 4 3 0 Enlarged character size.
4 4 3 1 Graphic Print Speed. 4 5 3 2 Accent character. 4 5 3 3 Setting of the FF code at TOF. 4 5 H P m o d e e n h a n c e m e n t 3 8 PCL mode. 4 6 3 9 Secondary character table. 4 6 P a p e r h a n d l i n g e n h a n c e m e n t 4 0 Set the top margin.
4 7 4 1 Set the bottom margin. 4 7 4 2 Set the left margin. 4 7 4 3 Set the right margin. 4 8 4 4 Fanfold paper width. 4 8 4 5 Autoscroll delay. 4 8 4 6 Override bottom margin. 4 9 4 7 Label mode.
4 9 4 8 Paper out detection. 5 0 4 9 Cut sheet feeder type. 5 0 5 0 Setting of the auto scrolling position. 5 0 5 1 Line Feed Speed. 5 1 C o m m u n i c a t i o n e n h a n c e m e n t 6 0 Interface type. 5 1 6 1 SELECT IN signal.
5 4 7 3 Data latch timing. 5 4 7 4 Setting of whether ERROR/PE signals are output or not. 5 4 M i s c e l l a n e o u s 8 0 Print direction. 5 5 8 1 LCD display language. 5 5 8 2 Invert LCD display. 5 5 8 3 Software controlled setup.
5 6 8 4 Lock the RESET key. 5 6 8 5 Setting of ENERGY STAR.
5 6 8 6 Saving user setup options. 5 6 8 7 Printing list of option settings. Setting the application software About printer driver. 5 7 Printer driver selection. 5 7 Connecting the BP-9000 printer in the HP Environment. 5 8 Saving Your Setup.
6 4 Vertical alignment mode. Bar code and enlarged character function Bar code function Outline of bar code function. 6 9 Makeup of bar code. 6 9 Bar code command list. 7 0 (1) Bar code type.
7 0 (2) Element width. 7 1 (3) Bar code height. 7 1 (4) Setting HRI on and off. 7 1 (5) HRI font. 7 2 (6) Check character.
7 2 (7) Starting the bar code data sequence. 7 2 (8) Ending the bar code data sequence. 7 3 (9) Bar code data sequence. 7 3 (10) Printing density. 7 3 (11) Guide bar expansion. 7 3 (12) Start and stop characters.
7 4 (13) Barcode rotational angle. 7 4 (14) Disabling HRI of the start and stop characters.
7 4 (15) Value input mode. 7 4 (16) Initializing the bar code mode. 7 5 Data processing in the bar code data sequence. 7 5 Printing bar codes. 7 6 Error processing.
7 7 Code 128 subset transition rule. 7 7 UPC-E conversion rule. 7 8 Calculating the check character. 8 0 Element printing. 8 0 Enlarged character function Outline of enlarged characterfunction. 8 2 Enlarged character command list.
8 4 (5) Initializing the enlarged character mode. 8 4 (6) Arrangement of enlarged characters. 8 5 (7) Cell magnification for enlarged characters. 8 5 (8) All-character set for enlarged characters.
8 6 (9) Selecting an enlarged character font. 8 6 (10) Height expansion for enlarged characters. 8 7 (11) HMI for enlarged characters. 8 7 (12) VMI for enlarged characters. 8 8 (13) Setting and canceling the enlarged character mode. 8 8 (14) Enlarged character cell offset. 8 9 (15) Enlarged character pitch.
8 9 (16) Enlarged character quality. 9 0 (17) Enlarged character rotational angle. 9 0 (18) Setting and canceling enlarged character smoothing. 9 1 (19) Enlarged character top offset.
9 1 (20) Setting and canceling underlining of enlarged characters. 9 2 (21) Enlarged character widthwise expansition. 9 2 (22) Horizontal printing position for enlarged characters. 9 3 (23) Vertical printing position for enlarged characters. 9 3 Enlarged character print samples. Appendices A. Specifications Printing specifications.
1 0 1 Other specifications. Control code summary IBM mode.
1 0 3 Epson mode. 1 0 9 PCL mode. 11 5 Setup options control codes. Caution for use Power sourc e. Be sure to insert the power plug only in a wall unit of the voltage designated in the voltage selector switch and on the rating plate on the back of the unit.
Do not place the power cord near heat sources or place heavy objects on it. Do not bend or twist the power cord. Foreign matter and water.
Keep your hands and personal items, such as scarfs and ties, away from the carriage mechanism while the printer is operating. The carriage moves with considerable force. Keep the printer dry. If you accidentally spill water on the machine, turn the power off immediately and wipe it dry. Do not turn t h e p o w e r o n u n t i l t h e m a c h i n e i s completely dry.
Installation environment. The printer should be used where humidity is low, where there is little dust, and where the printer is not in direct sunlight. Avoid placing or leaning anything on top of the printer. If you accidentally drop any object into the machine, turn the power off immediately, then carefully remove the object. Do not twist the ribbon while installing it. Operating condition.
Wait at least two seconds after turning power o ff b e f o r e t u r n i n g i t b a c k a g a i n. T h e initialization process may not be performed correctly if this is not done. Do not touch the print head immediately after printing because it is too hot. Never operate the printer without paper or paper properly installed. If you use paper that is not as wide as the platen, be sure that printing does not exceed paper width.
Use software control to change the width of the print line. Never insert or pull out an interface cable while the power to the printer and computer is on. Be sure to turn off the printer before turning off a connected host computer.
. Smart Label Printers ® Series User Guide Models 440 and 450 For Windows 2000, XP, 2003, Server 2003, Vista and Windows 7 ® or Mac OS X 10.2 or later. Caution statements are used to indicate actions. Increase the separation between the equipment and receiver.
That may result in damage to the printer or other property, or. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. May result in risk of minor personal injury. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by Seiko Instruments could void the user’s authority to operate the equipment.
Warning Applicable EC Directives and Standards Directive Title 1 Use only the AC adapter provided with this printer, or an AC adapter that has been. This guide has six sections for easy reference: 6 Before using your SLP, please remove the clear protective tape covering on the engine cover and Roll cover. Introduction, provides some general information about the SLP 440 and 450 as well as the Smart Label program. 7 When the SLP is unused for a period of time without a label, the platen rubber may become stuck. This condition may cause a fatal error in the printer mechanism. To avoid Getting Started, provides instructions for connecting the SLP 440 and 450 to your Windows- this, please keep a label loaded in the SLP — even when not in use. Compatible PC or Mac, and loading labels into the printer.
It also describes how to use on-line help. Installation Changing Labels and Printer Care, provides information for replacing a label roll and taking care of your SLP. For best performance, we recommend that you install your printer on a flat surface in a location that satisfies the following environmental conditions: Specifications, provides SLP 440 and 450 specifications.
The Smart Label program provides a rich set of features to simplify your labeling needs. Adjusting the Position of Labels Removing Stuck Labels. WYSIWYG editor displays labels as they will print. Cleaning the Printer. Prints in background so you can work with other applications while labels are printing.
Print labels one at a time or whole mailing lists. Specifications. Object-oriented user interface makes it easy to include text, pictures, bar codes, etc. Smart Label Printer 440 and 450 Specifications on your label. Status Light Indicators.
Mixed text possible within each text object—different font types, sizes and styles (bold/ Commonly Asked Questions and Answers italic/underline) can be included on a single line. Shrink-to-fit and word wrap ensure that addresses and other text fit on the label. Technical Support and Service. Built-in database to save labels and formats in user-definable database categories. PC Users: The SmartLabels have a sensor mark on the backing of each label that the SLP 440 and.
Windows 2000, XP, 2003, Server 2003, Vista or Windows 7 450 uses for top of label alignment. Check to be sure the labels have this mark before. IBM ® PC or compatible using 233MHz or higher Pentium-compatible CPU loading them into the SLP. Minimum 64MB RAM, 128MB recommended. 16MB hard disk space. USB port or RS232C serial port.
CD-ROM or DVD drive Sensor mark Note: Older SmartLabels did not have this sensor mark. Be sure that the SLP 440 and 450 Mac Users: are listed as supported printers on the SmartLabels package. Mac OS X v10.2 or later. PowerPC ® G3/G4/G5 or Intel ® processor Caring for Labels.
Minimum 128MB RAM, 256MB recommended. 30MB hard disk space The labels are sensitive to heat, moisture, and light. With this in mind:. USB port. Installing the SLP 440 or 450 Installing the Software Installing the Smart Label Program for MacOS X Here, you’ll find out how to unpack and set up your new SLP.
As part of the setup process, you’ll load a roll of standard address labels and run a quick test. 1 Insert the Smart Label CD. If the installer does not appear automatically, double-click the CD on your desktop or in the left pane of a new Finder window.
Unpacking the SLP 2 Double-click the file SIISmartLabelPrinter.mpkg. The installer will appear. Follow the on-screen instructions. Carefully remove the printer and its components from the box. It’s a good idea to save the 3 For Mac OS X 10.2: After installation is complete, open Print Center and select your SLP box and packing materials in case you need to store or ship the printer. Make sure you printer.
Mac OS X 10.3 or 10.4 will automatically set up your printer. Connecting the SLP to your computer Setting up the Printer Use the USB cable provided with the SLP 440 or 450 to connect the SLP to your computer. If the printer is not recogonized using the installation wizard, you will need to set up your printer manually.
To do so, follow these steps: CAUTION: Connecting or disconnecting the interface cable Prepare the roll of labels while the printer is turned on may damage the printer. 4 Insert the labels and spindle into the SLP. If necessary, adjust the guides to fit the A quick test lets you know your printer is operating properly and that the labels labels as shown below. Are loaded correctly. Testing the SLP 440 or 450 1 Press and hold the power button for 2 seconds to turn the printer off. 2 Press and hold the form feed button and then press the power button. The green status light will begin to flash.
Do not release the form feed button. You can load a different type of label at any time — you don’t have to wait until all of the labels have been used. Your SLP 440 and 450 is a high-precision device that’s designed for trouble-free operation. When you run out of labels, the green status light on the front of the SLP flashes. If printing Just follow these few precautions: is in process, a message appears telling you that the printer is out of labels. Note: The SLP 440 and 450 is designed for use only with Seiko Instruments SmartLabels. Use of improper labels may damage the printer and void your warranty.
Removing the Old Roll. Don’t operate the printer in a dusty environment. CAUTION: DO NOT pull on the labels to remove them from the. Keep the printer out of direct sunlight. 2 Release the pressure on the label stock by moving the platen release lever forward. 2 Swivel the label cover open and remove the print engine cover by pulling forward on the edges at the top of the cover. 3 Release the pressure on the label stock by moving the platen release lever forward.
Remove the print engine cover 4 Remove the stuck label. 5 If the label – or pieces of the label – stick to the platen, use the Seiko Dual-Action Cleaning Pen to dissolve the adhesive on the label and remove residue left on the printer. CAUTION: DO NOT touch the print engine. It may be hot.
Release the platen lever 3 Realign the label stock so it is straight. 4 Return the platen release lever to the locked position. Cleaning the Printer You may also purchase the Seiko Dual-Action Cleaning Pen (SLP-CLNPEN) to help keep the printer clean and operating at it’s optimum.
1 Remove label stock from printer. Removes Adhesive 2 Insert the Seiko Smart Label Printer Cleaning Card (SLP-CLNCRD). 3 The Card should feed automatically or you can press the “Form Feed” button to manually feed the card (you may also gently pull the card to guide it through the roller).
Cleans the print head Form Feed button 1 Remove label stock from printer. Specifications Environment Temperature Operating: 59°F to 95°F (15°C to 35°C ) Smart Label Printer 440 and 450 Storage: -4°F to 140°F (-20°C to 60°C) Humidity Operating: 30% RH to 80% RH The Smart Label Printer is a compact printing device ideally suited for label printing (non-condensing) applications. There are no built-in fonts and any text must be converted to a bitmap image Storage: 30% RH to 90% RH by a host computer or device for printing.
(non-condensing) Developer information can be found on our website at www.siibusinessproducts.com Printer Technology Direct thermal Resolution 300 dpi (11.81 dots/mm) Max. Paper Width 2.28 in. (58mm) Status Light Indicators Max. Commonly Asked Questions Technical Support and Service and Answers Please refer to the “Troubleshooting” topic in on-line Help for information on how to determine if your Smart Label Printer needs service and how to contact Seiko Instruments Q Will my labels fade over time?
For Technical Support and repairs. A Labels are made of thermal paper. Heat applied to the paper causes a chemical You can contact Technical Support on our website under the Support section at: reaction to generate black dots at the points where heat was applied.
This technique www.siibusinessproducts.com avoids using messy inks and ribbons. Because the paper is heat-sensitive, it is possible for a label to darken if exposed to high heat or very bright light for an extended period of time. It is also possible for certain plasticizers in some plastic binders to cause a Ordering Labels and Parts chemical reaction which results in the image fading over time. Placing another.